View MC-454CB646_638543.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA SHEET
MOS INTEGRATED CIRCUIT
MC-454CB646
4M-WORD BY 64-BIT SYNCHRONOUS DYNAMIC RAM MODULE UNBUFFERED TYPE
Description
The MC-454CB646 is a 4,194,304 words by 64 bits synchronous dynamic RAM module on which 4 pieces of 64M SDRAM : PD4564163 (Revision E) are assembled. This module provides high density and large quantities of memory in a small space without utilizing the surfacemounting technology on the printed circuit board. Decoupling capacitors are mounted on power supply line for noise reduction.
Features
* 4,194,304 words by 64 bits organization * Clock frequency and clock access time
Family /CAS latency Clock frequency (MAX.) MC-454CB646-A80 CL = 3 CL = 2 MC-454CB646-A10 CL = 3 CL = 2 125 MHz 100 MHz 100 MHz 77 MHz Clock access time (MAX.) 6 ns 6 ns 6 ns 7 ns Power consu mption (MAX.) Active 2,808 mW 2,376 mW 2,376 mW 1,872 mW Standby 7.2 mW (CMOS level input )
* Fully Synchronous Dynamic RAM, with all signals referenced to a positive clock edge * Pulsed interface * Possible to assert random column address in every cycle * Quad internal banks controlled by BA0 and BA1 (Bank Select) * Programmable burst-length : 1, 2, 4, 8 and full page * Programmable wrap sequence (sequential / interleave) * Programmable /CAS latency (2, 3) * Automatic precharge and controlled precharge * CBR (Auto) refresh and self refresh * All DQs have 10 10 % of series resistor * Single 3.3 V 0.3 V power supply * LVTTL compatible * 4,096 refresh cycles / 64 ms * Burst termination by Burst Stop command and Precharge command * 168-pin dual in-line memory module (Pin pitch = 1.27 mm) * Unbuffered type * Serial PD
The information in this document is subject to change without notice.
Document No. M13342EJ2V0DS00 (2nd edition) Date Published April 1998 NS CP (K) Printed in Japan
The mark * shows major revised points.
(c)
1998
MC-454CB646
Ordering Information
Part number Clock frequency (MAX.) MC-454CB646F-A80 125 MHz 168-pin Dual In-line Memory Module (Socket Type) MC-454CB646F-A10 100 MHz Edge connector : Gold plated 34.93 mm (1.375 inch) height [Single side] 4 pieces of PD4564163G5 (Revision E) (400 mil TSOP (II)) Package Mounted devices
2
MC-454CB646
Pin Configuration
168-pin Dual In-line Memory Module Socket Type (Edge connector: Gold plated) [MC-454CB646F] /XXX indicates active low signal.
85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 VSS DQ32 DQ33 DQ34 DQ35 Vcc DQ36 DQ37 DQ38 DQ39 DQ40 VSS DQ41 DQ42 DQ43 DQ44 DQ45 Vcc DQ46 DQ47 NC NC VSS NC NC Vcc /CAS DQMB4 DQMB5 NC /RAS VSS A1 A3 A5 A7 A9 BA0 (A13) A11 Vcc CLK1 NC VSS CKE0 NC DQMB6 DQMB7 NC Vcc NC NC NC NC VSS DQ48 DQ49 DQ50 DQ51 Vcc DQ52 NC NC NC VSS DQ53 DQ54 DQ55 VSS DQ56 DQ57 DQ58 DQ59 Vcc DQ60 DQ61 DQ62 DQ63 VSS CLK3 NC SA0 SA1 SA2 Vcc VSS DQ0 DQ1 DQ2 DQ3 Vcc DQ4 DQ5 DQ6 DQ7 DQ8 VSS DQ9 DQ10 DQ11 DQ12 DQ13 Vcc DQ14 DQ15 NC NC VSS NC NC Vcc /WE DQMB0 DQMB1 /CS0 NC VSS A0 A2 A4 A6 A8 A10 BA1(A12) Vcc Vcc CLK0 VSS NC /CS2 DQMB2 DQMB3 NC Vcc NC NC NC NC VSS DQ16 DQ17 DQ18 DQ19 Vcc DQ20 NC NC NC VSS DQ21 DQ22 DQ23 VSS DQ24 DQ25 DQ26 DQ27 Vcc DQ28 DQ29 DQ30 DQ31 VSS CLK2 NC WP SDA SCL Vcc 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84
A0 - A11 BA0 (A13), BA1 (A12) DQ0 - DQ63 CLK0, CLK1 CKE0 WP /CS0, /CS2 /RAS /CAS /WE SA0 - SA2 SDA SCL VCC VSS NC
: Address Inputs
[Row : A0 - A11, Column : A0 - A7] : SDRAM Bank Select : Data Inputs / Outputs : Clock Input : Clock Enable Input : Write Protect
Note
: Chip Select Input : Row Address Strobe : Column Address Strobe : Write Enable : Address Input for EEPROM : Serial Data I/O for PD : Clock Input for PD : Power Supply : Ground : No Connection
DQMB0 - DQMB7 : DQ Mask Enable
Note WP is not used yet. It is connected to ground.
3
MC-454CB646
* Block Diagram
/WE
/CS0 DQMB 4
LDQM /CS /WE
/CS2 DQMB 6
LDQM /CS /WE
DQ 32 DQ 33 DQ 34 DQ 35 DQ 36 DQ 38 DQ 37 DQ 39
DQMB 0
DQ 0 DQ 1 DQ 2 DQ 3 DQ 4 DQ 5 DQ 6 DQ 7
UDQM U1
DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55
DQMB 2
DQ 0 DQ 1 DQ 2 DQ 3 DQ 4 DQ 5 DQ 6 DQ 7
U4 UDQM
DQ 7 DQ 6 DQ 5 DQ 4 DQ 3 DQ 2 DQ 1 DQ 0
DQ 8 DQ 9 DQ 10 DQ 11 DQ 12 DQ 13 DQ 14 DQ 15
DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23
DQ 8 DQ 9 DQ 10 DQ 11 DQ 12 DQ 13 DQ 14 DQ 15
DQMB 5
LDQM
/CS /WE
DQMB 7
LDQM
/CS /WE
DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47
DQMB 1
DQ 0 DQ 1 DQ 2 DQ 3 DQ 4 DQ 5 DQ 6 DQ 7
U2 UDQM
DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63
DQMB 3
DQ 0 DQ 1 DQ 2 DQ 3 DQ 4 DQ 5 DQ 6 DQ 7
U5 UDQM
DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8
DQ 8 DQ 9 DQ 10 DQ 11 DQ 12 DQ 13 DQ 14 DQ 15
DQ31 DQ30 DQ29 DQ28 DQ27 DQ26 DQ25 DQ24
DQ 8 DQ 9 DQ 10 DQ 11 DQ 12 DQ 13 DQ 14 DQ 15
SERIAL PD SDA SCL A0 A1 A2 WP
CLK0
CLK : U1, U2 10 pF+3.3 pF
CLK2
47 k
SA0 SA1 SA2 CLK1, CLK3 A0 - A11 BA0 BA1 VCC C VSS U1, U2, U4, U5 CKE0 A0 - A11: U1, U2, U4, U5 A13: U1, U2, U4, U5 A12: U1, U2, U4, U5 U1, U2, U4, U5 /RAS /CAS
CLK : U4, U5 15 pF
10 pF
/RAS: U1, U2, U4, U5 /CAS: U1, U2, U4, U5 CKE: U1, U2, U4, U5
Remarks 1. The value of all resistors is 10 except WP. 2. WP is not used yet. It is connected to ground. 3. U1, U2, U4, U5 : PD4564163 (Revision E)(1M words x 16 bits x 4 banks) 4
MC-454CB646
Electrical Specifications
* All voltages are referenced to VSS (GND). * After power up, wait more than 100 s and then, execute power on sequence and auto refresh before proper device operation is achieved. Absolute Maximum Ratings
Parameter Voltage on power supply pin relative to GND Voltage on input pin relative to GND Short circuit output current Power dissipation Operating ambient temperature Storage temperature Symbol VCC VT IO PD TA Tstg Condition Rating -0.5 to +4.6 -0.5 to +4.6 50 4 0 to +70 -55 to +125 Unit V V mA W C C
Caution
Exposing the device to stress above those listed in Absolute Maximum Ratings could cause permanent damage. The device is not meant to be operated under conditions outside the limits described in the operational section of this specification. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter Supply voltage High level input voltage Low level input voltage Operating ambient temperature Symbol VCC VIH VIL TA Condition MIN. 3.0 2.0 -0.3 0 TYP. 3.3 MAX. 3.6 VCC+0.3 +0.8 70 Unit V V V C
* Capacitance (TA = 25 C, f = 1 MHz)
Parameter Input capacitance Symbol CI1 Test condition A0 - A11, BA0 (A13), BA1 (A12), /RAS, /CAS, /WE CI2 CI3 CI4 CI5 Data input / output capacitance CI/O CLK0, CLK2 CKE0 /CS0, /CS2 DQMB0 - DQMB7 DQ0 - DQ63 24 22 12 7 7 40 40 20 13 13 pF MIN. 22 TYP. MAX. 40 Unit pF
5
MC-454CB646
DC Characteristics (Recommended Operating Conditions Unless Otherwise Noted)
Parameter Operating current Symbol ICC1 Burst length = 1, tRC tRC (MIN.), IO = 0 mA /CAS latency = 3 Test condition /CAS latency = 2 Grade -A80 -A10 -A80 -A10 Precharge standby current in power down mode Precharge standby current in non power down mode ICC2NS Active standby current in power down mode ICC3P ICC3PS ICC3N ICC2P ICC2PS ICC2N CKE VIL (MAX.), tCK = 15 ns CKE VIL (MAX.), tCK = CKE VIH (MIN.), tCK = 15 ns, /CS VIH (MIN.), Input signals are changed one time during 30 ns. CKE VIH (MIN.), tCK = , Input signals are stable. CKE VIL (MAX.), tCK = 15 ns CKE VIL (MAX.), tCK = CKE VIH (MIN.), tCK = 15 ns, /CS VIH (MIN.), Input signals are changed one time during 30 ns. ICC3NS Operating current (Burst mode) /CAS latency = 3 ICC4 CKE VIH (MIN.), tCK = , Input signals are stable. tCK tCK (MIN.), IO = 0 mA /CAS latency = 2 -A80 -A10 -A80 -A10 Refresh current ICC5 /CAS latency = 2 -A80 -A10 /CAS latency = 3 -A80 -A10 Self refresh current Input leakage current Output leakage current ICC6 II (L) IO (L) VOH VOL CKE 0.2 V VI = 0 to 3.6 V, All other pins not under test = 0 V DOUT is disabled, VO = 0 to 3.6 V IO = -4.0 mA IO = +4.0 mA -4 -1.5 2.4 0.4 40 660 520 780 660 520 520 540 540 4 +4 +1.5 mA mA 3 mA 2 24 20 16 100 mA mA MIN. MAX. 360 320 460 360 4 2 80 mA mA Unit Notes mA 1
* *
*
Active standby current in non power down mode
A A
V V
* *
High level output voltage Low level output voltage
Notes 1. ICC1 depends on output loading and cycle rates. Specified values are obtained with the output open. In addition to this, ICC1 is measured on condition that addresses are changed only one time during tCK (MIN.). 2. ICC4 depends on output loading and cycle rates. Specified values are obtained with the output open. In addition to this, ICC4 is measured on condition that addresses are changed only one time during tCK (MIN.). 3. ICC5 is measured on condition that addresses are changed only one time during tCK (MIN.).
6
MC-454CB646
AC Characteristics (Recommended Operating Conditions Unless Otherwise Noted)
AC Characteristics Test Conditions * AC measurements assume tT = 1 ns. * Reference level for measuring timing of input signals is 1.4 V. Transition times are measured between VIH and VIL. * If tT is longer than 1 ns, reference level for measuring timing of input signals is VIH (MIN.) and VIL (MAX.). * An access time is measured at 1.4 V.
tCK tCH CLK 2.0 V 1.4 V 0.8 V tSETUP tHOLD 2.0 V 1.4 V 0.8 V tAC tOH Output tCL
Input
7
MC-454CB646
Synchronous Characteristics
Parameter Symbol MIN. Clock cycle time /CAS latency = 3 /CAS latency = 2 Access time from CLK /CAS latency = 3 /CAS latency = 2 CLK high level width CLK low level width Data-out hold time Data-out low-impedance time Data-out high-impedance time /CAS latency = 3 /CAS latency = 2 Data-in setup time Data-in hold time Address setup time Address hold time CKE setup time CKE hold time CKE setup time (Power down exit) Command (/CS0, /CS2, /RAS, /CAS, /WE, DQMB0 - DQMB7) setup time Command (/CS0, /CS2, /RAS, /CAS, /WE, DQMB0 - DQMB7) hold time tCMH 1 1 ns tCK3 tCK2 tAC3 tAC2 tCH tCL tOH tLZ tHZ3 tHZ2 tDS tDH tAS tAH tCKS tCKH tCKSP tCMS 3 3 3 0 3 3 2 1 2 1 2 1 2 2 6 6 8 10 -A80 MAX. (125 MHz) (100 MHz) 6 6 3 3 3 0 3 3 2 1 2 1 2 1 2 2 6 7 MIN. 10 13 -A10 MAX. (100 MHz) (77 MHz) 6 7 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 1 1 1 Unit Note
Note 1. Output load
1.4 V Z = 50 Output 50 pF 50
*
Remark These specifications are applied to the monolithic device.
8
MC-454CB646
Asynchronous Characteristics
Parameter Symbol MIN. REF to REF/ACT command period ACT to PRE command period PRE to ACT command period Delay time ACT to READ/WRITE command ACT (0) to ACT (1) command period Data-in to PRE command period Data-in to ACT (REF) command period (Auto precharge) Mode register set cycle time Transition time Refresh time /CAS latency = 3 /CAS latency = 2 tRC tRAS tRP tRCD tRRD tDPL tDAL3 tDAL2 tRSC tT tREF 70 48 20 20 16 8 1CLK+20 1CLK+20 2 0.5 30 64 120,000 -A80 MAX. MIN. 70 50 20 20 20 10 1CLK+20 1CLK+20 2 1 30 64 120,000 -A10 MAX. ns ns ns ns ns ns ns ns CLK ns ms Unit Note
9
MC-454CB646
Serial PD
Byte No. 0 Defines the number of bytes written into serial PD memory 1 Total number of bytes of serial PD memory 2 3 4 5 6 7 8 9 Fundamental memory type Number of rows Number of columns Number of banks Data width Data width (continued) Voltage interface CL = 3 cycle time -A80 -A10 10 CL = 3 access time -A80 -A10 11 12 13 14 15 16 17 18 19 20 21 22 23 DIMM configuration type Refresh rate / type SDRAM width Error checking SDRAM width Minimum clock delay Burst length supported Number of banks on each SDRAM /CAS latency supported /CS latency supported /WE latency supported SDRAM module attributes SDRAM device attributes : General CL = 2 cycle time -A80 -A10 24 CL = 2 access time -A80 -A10 25-26 27 tRP (MIN.) -A80 -A10 28 tRRD (MIN.) -A80 -A10 29 tRCD (MIN.) -A80 -A10 30 tRAS (MIN.) -A80 -A10 04H 0CH 08H 01H 40H 00H 01H 80H A0H 60H 60H 00H 80H 10H 00H 01H 8FH 04H 06H 01H 01H 00H 0EH A0H D0H 60H 70H 00H 14H 14H 10H 14H 14H 14H 30H 32H 08H 0 0 0 0 0 0 0 1 1 0 0 0 1 0 0 0 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 1 1 1 1 1 1 1 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 0 0 0 0 0 1 1 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 20 ns 20 ns 10 ns 20 ns 20 ns 20 ns 48 ns 50 ns 32 bytes 10 ns 13 ns 6 ns 7 ns SDRAM 12 rows 8 columns 1 bank 64 bits 0 LVTTL 8 ns 10 ns 6 ns 6 ns None Normal x16 None 1 clock 1, 2, 4, 8, F 4 banks 2, 3 0 0 08H 0 0 0 0 1 0 0 0 256 bytes 80H 1 0 0 0 0 0 0 0 128 bytes Function Described Hex Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
(1/2)
Notes
*
*
10
31
Module bank density
MC-454CB646
(2/2)
Byte No. 32 33 Function Described Command and address signal input setup time Command and address signal input hold time 34 35 36-61 Data signal input setup time Data signal input hold time 20H 10H 00H SPD revision Checksum for bytes 0 - 62 -A80 -A10 64-71 72 73-90 91-92 93-94 95-98 Manufacture's JEDEC ID code Manufacturing location Manufacture's P/N Revision code Manufacturing date Assembly serial number 12H DEH 44H 0 0 0 0 1 0 0 0 0 0 1 1 1 0 0 0 0 0 0 1 0 1 1 0 0 0 0 0 1 0 0 0 0 0 1 1 0 0 0 1 1 0 0 0 0 0 0 0 1.2 2 ns 1 ns Hex 20H 10H Bit 7 0 0 Bit 6 0 0 Bit 5 1 0 Bit 4 0 1 Bit 3 0 0 Bit 2 0 0 Bit 1 0 0 Bit 0 0 0 Notes 2 ns 1 ns
* *
62 63
99-125 Mfg specific 126 127 Intel specification frequency Intel specification /CAS latency support -A80 -A10 64H A7H A5H 0 1 1 1 0 0 1 1 1 0 0 0 0 0 0 1 1 1 0 1 0 0 1 1 100 MHz
Timing Chart Please refer to NEC Synchronous DRAM Data sheet.
11
MC-454CB646
* Package Drawing
168 PIN DUAL IN-LINE MODULE (SOCKET TYPE)
N Y Z Q
R
S (OPTIONAL HOLES) A J I B G H K C D A E B
L
U
T
detail of W
part
detail of
part
ITEM A B C D E G
MILLIMETERS 133.350.13 11.43 36.83 6.35 54.61 6.35 1.27 (T.P.) 8.89 24.495 42.18 17.78 34.93 4.0 MAX. 1.0 R2.0 4.00.1 3.0 1.270.1 4.0 MIN. 0.20.15 1.00.05 2.54 MIN. 3.0 MIN. 3.0 MIN.
INCHES 5.2500.006 0.450 1.450 0.250 2.150 0.250 0.050 (T.P.) 0.350 0.964 1.661 0.700 1.375 0.158 MAX. 0.039 R0.079 0.157 +0.005 -0.004 0.118 0.050.004 0.157 MIN. 0.00787 0.0059 0.039 +0.003 -0.002 0.1000.004 0.118 MIN. 0.118 MIN.
V
X
H
G
P D
I J K L M N P Q R S T U V W X Y Z
12
M
MC-454CB646
[MEMO]
13
MC-454CB646
[MEMO]
14
MC-454CB646
NOTES FOR CMOS DEVICES
1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it.
2 HANDLING OF UNUSED INPUT PINS FOR CMOS
Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices.
3 STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function.
15
MC-454CB646
[MEMO]
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as the memory IC, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on these components to prevent damaging them. When re-packing memory modules, be sure the modules are NOT touching each other. Modules in contact with other modules may cause excessive mechanical stress, which may damage the modules.
No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product.
M4 96. 5

▲Up To Search▲

Price & Availability of MC-454CB646

	To Download MC-454CB646 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .